nlwxpearo
Joined: 13 Dec 2010
Posts: 520
Read: 0 topics
Warns: 0/5
Location: England
|
 Posted: Sat 22:04, 22 Jan 2011 Post subject: Tractor spill causes and blocking rule _706 |
|
|
Tractor spill causes and blocking rule
Method: Clear the debris between the ball and valve seat; if seat badly worn ball or wide, direct replacement parts; if the ball can be put into the bad seal the valve seat. Withstand with brass ball, brass percussion hammer and then make a good seal; replacing defective seals; tighten the nut or replace the nut. 2 Since the tight oil seal leak (i) of the original solid: deformed skeleton oil seal, oil seal lip wear. Journal severe wear. (2) blocking rule: replace a new seals, oil seals should be installed within a L level pressure, since the currency could fall off the spring tight seal, oil seal lip can be deformed skeleton; axis halo wear, should be surfacing repair. 3 flat seams leak (1) of the original solid: on uneven table, deformation damage. Gasket is damaged, the thickness of all, James is willing to impurities in the dirt. According to the specified tightening torque of nuts such as a coating on a relatively fixed component then sets the interface leakage, rubber sealant blocking rule. Is: �� thorough scrubbing with gasoline or detergent components, will be the counter sealant applied to the junction (connection table if gasket between the amine should be flooded in the surface of the gasket 2 g), coated blade or blades can be used when quickly spread evenly, the thickness of O. 06liftif1-0.10m,[link widoczny dla zalogowanych], n �� temperature must be above 5 ��. (Coated and placed a 3min 5min, until the formation of layers with a flexible plastic film and sticky and toughness can be installed when tightened. 2 minor grooves pad cracks. With needle files, fine sandpaper, then oil half a hundred other licensing table table if the connection severe warpage can be used in the chapter on the milling machine. if necessary,[link widoczny dla zalogowanych], replace kitchen facelift new gasket should be to ensure even contact surface clean. paper seal the two surfaces to be coated with butter. polished Results tone face, pull a net oil then coated with liquid sealant L table space hours. machi appropriate Cong thinner; at] gap, the seal should be added in the gasket 2 L liquid sealant top coat when the fastening nut must be graded by order of tightening the nut. tightening torque should not be too big 4. threaded pipe joint leakage I1) Harada: connector contacts are plane pull marks,[link widoczny dla zalogowanych], Au A. Or impurity complex; just damage to the gland; hollow threaded pipe connection and installation of the shell divination earth's surface a screw hole: not properly installed or nuts not tightened f2) block clearance method: H Whetstone polished with sandpaper or contact surface, to impurities dirt to replace the damaged seal. With needle files or sandpaper grinding the first section of the hollow body threaded surface of the thread Bu L, if necessary, on the milling machine in the post-field blocking rule tightening torque. 5, then sets cone fittings trickle of oil ...} l1) reasons: hose connector deformation or wear and tear with cracks; seal damage, deformation; tubing connector is not properly installed or slipping: Tighten the nut is not so. ( 2) blocking rule Methods: worn or deformed joints cut off the pipeline to re-solder a pipe joint; replacement of damaged seals, or other wrapped around the tubing string; thread slipping should be replaced with new parts. can also be re-buckle repair. Installation should pay attention to clean and put the positive and nut tightening torque required. 6 rotary oil fI) reasons: severe wear axis and L; decompression shaft cavity ring aging failure: (2) block method of treatment : will start the machine in the lathe and the clutch lever shaft turning a shaft seal ring groove, install the appropriate size of the sealing rubber ring; replacement of the apron. 7 Wei oil drain plug oil block (I1 reason: oil plug thread cell damage or station. Screw L screw is damaged, badly worn conical plug (2) blocking treatment method: replacement of the drain plug screw, increase the size of Lo L, equipped with new oil block. with a tap after tapping block to peace , and then refitted with padded leakage oil filter cover and exhaust L and other end station interface. colloid can be installed asbestos, better governance leakage. �� low pressure hose connector leakage. drawer fastening the storage process,[link widoczny dla zalogowanych], the metal pad with the screw to rotate and compression the pad surface is caused by out of grooves. solution is to move the way: the pad surface can be polished, but also in the metal pad of the two side pieces of equipment plus�� thin mat made of plastic, the thickness 0I [nifl ~ 03mm �� For the governor shaft at both ends of the leakage, you can use inner tube rubber from {6 {installed in the governor shaft ends, the axial clamping force to prevent leakage of Ep. �� There will be tight in the hole made degree leather pads mounted on the starter shaft speed,[link widoczny dla zalogowanych], shaft and host from Taiwan decompression shaft, axial compression can be o �� favorite sayings - how you want to hoon who hold their own on, how you treat others. - Marx
The post has been approved 0 times
|
|
